Is your Whirlpool washer stuck with water inside and not draining properly? You’re not alone, and this problem can quickly turn a simple laundry day into a frustrating experience.
When your washer won’t drain, clothes stay soaked, and your whole routine gets disrupted. But don’t worry—understanding why this happens and how to fix it can save you time, money, and stress. Keep reading, and you’ll discover easy steps to get your Whirlpool washer draining like new again.
Common Drainage Issues
Drainage problems are common in Whirlpool washers. These issues stop water from leaving the machine properly. Water may stay inside, causing clothes to stay wet and smelly. Identifying the cause of drainage issues is important for quick fixes.
Three main parts often cause drainage problems: the drain hose, pump filter, and drain pump. Checking these parts can help find and solve the problem fast.
Clogged Drain Hose
The drain hose carries water out of the washer. Dirt, lint, and small objects can block it. A clogged hose stops water flow. This causes the washer to fill with water and not drain. Inspect the hose for kinks or blockages. Cleaning or replacing the hose can restore drainage.
Blocked Pump Filter
The pump filter traps debris before water drains. Over time, it fills up with lint and small items. A blocked filter prevents water from draining. Remove the filter to check for dirt or objects. Clean the filter to improve water flow and drainage.
Faulty Drain Pump
The drain pump pushes water out of the washer. If the pump breaks, water stays inside. Signs of a faulty pump include strange noises or no water movement. Testing the pump helps find problems. Replacing a bad pump fixes drainage issues and keeps the washer working well.
Credit: www.youtube.com
Quick Troubleshooting Steps
When your Whirlpool washer does not drain, quick troubleshooting helps save time. These simple checks can find common blockages or faults. Follow each step carefully to fix the issue fast.
Check And Clear Drain Hose
Start by inspecting the drain hose. Make sure it is not bent or twisted. Remove the hose from the washer and check for clogs. Use a long brush or water to clear any blockage. Reattach the hose firmly to avoid leaks.
Clean The Pump Filter
Next, clean the pump filter. This filter traps lint and small objects. Locate it at the front bottom of the washer. Open the access panel and remove the filter. Rinse it well under running water. Put the filter back securely before testing the washer.
Inspect The Drain Pump
Finally, check the drain pump for damage or blockages. Listen for unusual noises during the drain cycle. Remove any debris or foreign objects stuck in the pump. Ensure the pump blades can turn freely. Replace the pump if it looks broken or worn out.
Tools You’ll Need
Fixing a Whirlpool washer that does not drain requires a few simple tools. Having the right tools makes the job easier and faster. This section lists the basic hand tools and cleaning supplies you need.
Basic Hand Tools
Start with a set of screwdrivers. Both flathead and Phillips screwdrivers are important. You may need pliers to grip and turn parts. A wrench or socket set helps to remove bolts. A flashlight is useful to see inside dark areas. Keep a bucket nearby to catch any water.
Cleaning Supplies
Cleaning is key to fixing drainage problems. Have a sponge or cloth ready to wipe surfaces. A small brush helps to clean tight spaces. Use a mild detergent or vinegar to remove dirt. Avoid harsh chemicals that can damage parts. Gloves protect your hands during cleaning tasks.
Credit: lakeappliancerepair.com
Diy Drain Pump Replacement
Replacing the drain pump on your Whirlpool washer can fix draining problems fast. This task does not need a pro. With some tools and care, you can do it yourself.
Drain pumps often wear out or get clogged. Replacing the pump restores the washer’s ability to drain water properly. Follow the steps below to remove the old pump and install a new one safely.
Removing The Old Pump
Start by unplugging the washer from the power source. Safety first. Next, move the washer away from the wall to access the back panel.
Use a screwdriver to remove the screws holding the back panel. Take off the panel to see the drain pump. It usually sits at the bottom of the washer.
Disconnect the wires connected to the pump carefully. Remember their position or take a photo for reference. Then, remove the hose clamps and pull the hoses off the pump.
Loosen the screws or clips holding the pump in place. Take out the old pump and set it aside.
Installing The New Pump
Place the new pump in the same position as the old one. Secure it with screws or clips. Make sure it fits tight and does not move.
Reconnect the hoses to the pump. Tighten the hose clamps to avoid leaks. Attach the wires to the correct terminals as shown in your photo.
Put the back panel on and screw it back in place. Push the washer back to its original spot.
Plug the washer in and run a drain cycle. Check for leaks and proper water draining. The new pump should solve your draining problem.
Preventive Maintenance Tips
Preventive maintenance helps keep your Whirlpool washer working well. Small actions can stop big problems. Draining issues often come from neglect. Taking care early saves time and money.
Regular Filter Cleaning
Clean the washer filter every few weeks. The filter catches lint and debris. Dirt buildup can block water flow. Remove the filter gently and rinse it under water. Let it dry before placing it back. This keeps water draining smoothly. It also prevents bad smells inside the machine.
Avoiding Drain Blockages
Check the drain hose regularly for clogs. Clear any lint or dirt stuck inside. Avoid washing very dirty clothes without a pre-rinse. Large items can trap debris in the drain pipe. Keep the drain hose free from kinks or bends. These can stop water from flowing out. A clear drain means faster draining and fewer repairs.
Credit: royalappliance.cc
When To Call A Professional
Knowing when to call a professional for a Whirlpool washer not draining saves time and stress. Some problems need expert tools and skills. Avoid risking damage or injury by trying complex repairs alone. Here are signs that show it is time to get help.
Complex Electrical Issues
Electrical problems can cause the washer to stop draining. Faulty wiring or a broken control board needs a trained technician. These parts require special knowledge to test and fix safely. Avoid opening electrical components without experience. A professional can diagnose and repair these issues quickly.
Persistent Drain Problems
Persistent draining issues mean simple fixes did not work. Blocked hoses or pumps may need replacement. Sometimes the problem hides deeper inside the machine. Professionals have tools to find hidden clogs or worn parts. Calling an expert prevents ongoing frustration and saves your washer.
Frequently Asked Questions
Why Is My Whirlpool Washer Not Draining Water?
A clogged drain hose or pump filter often blocks water from draining properly.
How Do I Fix A Clogged Drain Pump In Whirlpool Washer?
Clean the pump filter and remove any debris blocking the drain pump.
Can A Broken Lid Switch Cause Whirlpool Washer Not To Drain?
Yes, a faulty lid switch can stop the washer from draining during cycles.
What Role Does The Drain Hose Play In Washer Draining Issues?
The drain hose removes water; if kinked or clogged, draining will fail.
When Should I Call A Technician For Whirlpool Washer Draining Problems?
Call a technician if cleaning and simple checks don’t fix the draining issue.
Conclusion
A Whirlpool washer not draining can cause big problems. Check the drain hose and filter for clogs. Clear any blockages to help water flow out. Sometimes, the pump may need attention or replacement. Regular maintenance keeps your washer working well.
Small fixes save time and money. Stay calm and follow simple steps to solve the issue. Your washer can run smoothly again with a little care. Don’t ignore the problem; act quickly to avoid damage. Clean, drain, and dry – that’s the key.